500 Abarth
1.4L I4 Turbo · 60,000 mi · Model only
5.9 researched
Research covers this year, model and mileage. Items marked addressed are reported by the owner and not verified by Squeezed. This is not a substitute for a pre-purchase inspection.
2013 Fiat 500 Abarth
This 2013 Fiat 500 Abarth is at the mileage where MultiAir hydraulic-control problems, clutch wear, oil leaks, and aging engine mounts deserve attention. New Firehawk tires are a useful positive, but they do not address the Abarth's higher-cost engine and drivetrain risks.
Budget about $6,200 for near-term catch-up if the clutch or MultiAir system shows symptoms. On the test drive, prioritize cold-start running quality, clutch engagement, and proof of regular oil changes. The asking price is somewhat above market.
Deal Score weighs the asking price against comparable listings, the title, and the repairs documented in this guide.
- Price 26% above market
Red flags
- Priced 26% Over Market
$9,800 asking against a typical $7,800 for this car
- MultiAir System
Documented hydraulic-control failures can cause rough running, misfires, or a no-start condition
- Clutch Wear
The manual clutch can be near replacement range at this age and mileage, especially with city use
Green flags
- New Firehawk Tires
Fresh tires improve wet and dry-road grip and remove an immediate replacement expense
When this car gets expensive
The chance of a major repair as the miles add up. This one is at 60k, before the climb starts around 96k.
What’s costing this car points
Fixing these, or marking them done, raises the score.
- −1.0
MultiAir Module Failure
Usually shows up around 70k mi - −0.5
Manual Clutch Slippage
Usually shows up around 80k mi - −0.2
Front Control Arm Bushing Wear
Usually shows up around 65k mi - 7 smaller items−0.3
Detailed findings, 10 items
Open a card for the full breakdown. Items the owner handled show as checked.
Reflects the open findings; items the owner handled are excluded.
Costly repairs. Price them in and use them to negotiate.
MultiAir Module Failure
The hydraulic variable valve timing module can lose oil pressure or develop an internal solenoid fault, causing rough running, misfires, reduced power, or a no-start condition. Failures are reported across early Fiat 500 Abarth cars and can appear around this mileage or later.
Manual Clutch Slippage
The clutch disc can slip under turbocharged engine torque, with engine speed rising faster than road speed during hard acceleration in higher gears. Engagement can also become high or grabby as the disc, pressure plate, and dual-mass flywheel age.
Turbo Oil Line Leakage
The turbocharger oil supply and return lines can seep at their fittings or seals, leaving oil around the turbocharger and producing a burning-oil smell after driving. A severe leak can reduce lubrication to the turbocharger and accelerate bearing damage.
Engine Mount Deterioration
The rubber in the engine and transmission mounts can crack or collapse, allowing excessive powertrain movement and causing clunks, vibration, or a thump when accelerating and lifting off the throttle. The turbocharged engine increases mount loading.
Front Control Arm Bushing Wear
The front suspension control-arm bushings can crack or soften, causing wandering, steering pull, braking-direction changes, or a dull knock over uneven pavement. The Abarth's firm suspension and low-profile tires increase the load on these bushings.
Minor wear for the car’s age. Worth tracking, not negotiating.
Oil Filter Housing Seepage
The oil filter housing gasket and nearby sealing surfaces can harden and seep engine oil onto the front or side of the engine. The first signs are oily residue, drops on the undertray, or a burning-oil smell when oil reaches a hot exhaust component.
Exhaust Flex Joint Cracking
The exhaust flex joint can crack or separate, creating a raspy exhaust leak, fumes, or a louder-than-normal exhaust note under acceleration. Movement from aging engine mounts can increase stress at this flexible section.
Air Conditioning Compressor Failure
The air conditioning compressor or its clutch can become noisy, fail to engage, or stop producing cold air as seals and bearings age. A failing compressor may shed debris through the refrigerant system and turn a simple leak repair into a larger system repair.
Battery Ground Connection Corrosion
Corrosion or looseness at the battery terminals and ground connections can cause intermittent warning lights, slow cranking, or electronic control-module faults. The car may appear mechanically normal while several unrelated electrical warnings appear together.
Turbocharger Boost Leak
The turbocharger charge-air hoses and clamps can loosen, split, or leak, causing hissing under boost, reduced acceleration, and sometimes an engine warning light. A leak can make the turbocharger work harder while the car feels noticeably slower.
Every finding still open carries a question worth asking. Copy them as one message, already ordered by severity. Anything you have marked above drops off on its own.
Price & negotiation
BetaBased on comparable listings and the repairs you can document. A starting point for what this car should cost.
Price breakdown
What it costs, and when
Verify now
Critical and major items to confirm first.
Possible year-one expense
Caution items with repair-cost context.
Each range is what that one item costs if it turns out to be present. Not every item will apply to this car, so they do not add up to a bill. Verify with a mechanic.
Asking is $9,800 against a typical $7,800 for this car and mileage. The work is the difference, not the sticker.
Negotiate your offer
At asking, this is about 26% above the market estimate (about $2,000). The documented repairs below are the kind of evidence buyers cite to start lower.
- Documented critical/major repairs of $3,900–$8,500 you can point to.
- Strongest items to raise first: Manual Clutch Slippage, MultiAir Module Failure.
Pricing is in beta. The market estimate comes from research models and can be off by thousands on the same car, so check recent local listings before you rely on it. This is information to help you research, not a professional inspection, an appraisal, or financial advice.
Recalls & safety
NHTSA crash-test ratings and recall data for this make, model, and year. Check recall status with your VIN before buying.
In-person inspection
10 things to check before you buy
5 major and 5 caution findings, turned into a walkthrough for the driveway. Answers save as you go.
Before you leave: Ask the seller not to start or move the car before you arrive. A sales-ready car has usually been warmed up, and a warm engine hides the startup smoke, rattles and rough idle that the first section is built around.
01Cold Start CheckFirst1
Start the engine cold while you watch the exhaust and listen. Note how quickly it catches, the tint of any smoke, rattles in the first few seconds, and how smoothly it settles into idle. This is the one test you cannot repeat on the spot.
02Underneath2
Get low with the flashlight while everything is still cool. Look for drips and oily residue, feel inside the tailpipe for black greasy soot, and check the rubber CV boots at the ends of the axles for splits throwing grease. Kinks in the frame rails, fresh weld marks, and new undercoating on an old car all point at repaired collision damage.
03Engine & Systems4
Before the first start: pull the oil dipstick and look for a milky film, check the coolant for oil or rust, squeeze the radiator hoses for hard or mushy spots, and note the battery date. Once warm: confirm the cooling fans cycle, listen for belt noise, look for fresh seepage that was not there cold, and check that the A/C blows cold.
04Test Drive2
Drive a route with stops, a hill, and some open road. Feel for shift quality, clutch or torque-converter behaviour, brakes that pull or pulse, steering play, and any noise that changes with speed or steering angle.
05Documentation1
Match the VIN across the title, dash, and door jamb. On a dealer lot, read the Buyers Guide sticker: it states whether the car carries a warranty or is sold as is, and as is means every repair after the sale is yours. Review service records and recall history, then run an OBD-II scan for stored and pending codes.
Everything on this list is what you can see standing next to the car. A shop on a lift sees the rest, and a written pre-purchase inspection listing parts and labor is what a seller has to answer to. Budget roughly $100 to $150 at an ASE-certified shop.
Get your own Buyer Guide
Same depth of analysis, personalized to the exact vehicle you're evaluating. Known failure patterns, repair cost exposure, and questions to ask the seller.
